Moxa serial convertersTCC-80I-DB9 Series
- Product Name： Moxa serial convertersTCC-80I-DB9 Series
- Product Number：TCC-80I-DB9 Series
- Brand：Moxa
- Views：109
-
Moxa serial convertersTCC-80I-DB9 Series
的详细介绍Moxa serial converters TCC-80I-DB9 Series
Introduction
The TCC-80/80I media converters provide complete signal conversion between RS-232 and RS-422/485, without requiring an external power source. The converters support both half-duplex 2-wire RS-485 and full-duplex 4-wire RS-422/485, either of which can be converted between RS-232’s TxD and RxD lines.
Automatic data direction control is provided for RS-485. In this case, the RS-485 driver is enabled automatically when the circuitry senses the TxD output from the RS-232 signal. This means that no programming effort is required to control the transmission direction of the RS-485 signal.
Port Power over RS-232
The RS-232 port of the TCC-80/80I is a DB9 female socket that can connect directly to the host PC, with power drawn from the TxD line. Regardless of whether the signal is high or low, the TCC-80/80I can obtain enough power from the data line. However, external power can be used if the handshake line is not available, if the serial cable is too long, or if the RS-232 device is a low-power device. For external power, a five to twelve VDC power supply can be connected using an adapter or a USB power cord.
Port Power DissipationWhen installing a TCC-80 or TCC-80I converter, it is important to pay attention to power consumption, RS-232 cable length, and RS-422/485 transmission distance. In general, the TCC-80 and TCC-80I obtain 50 mW of power from the power source. Standard PC COM ports can provide 70 to 90 mW of power if the TxD, RTS, and DTR lines are connected. Moreover, the RS-232 cable should be shorter than 15 m (@ 9600 bps) to ensure that less power is lost from the host/device to the TCC-80. The remainder of the supplied power is used for transmitting the RS-422/485 signal.
Port Power and Optical Isolation
The RS-232 port of the TCC-80/80I is a DB9 female socket that can connect directly to the host PC, with power drawn from the TxD line. Electrical 2.5 kV isolation for the TCC-80I is achieved with a photo coupler that transforms the electrical signal into light, and then re-transforms the light back into an electrical signal on the other side. In this way, the two electrical circuits are completely isolated from each other. This also protects the devices from ground loop currents, reduces damage caused by data loss, and prevents damage to the communication interfaces.
Moxa serial converters TCC-80I-DB9 Series
-
Connector
TCC-80-DB9/80I-DB9: DB9 male
TCC-80/80I: Terminal block -
No. of Ports
2
-
Serial Standards
RS-232, RS-422, RS-485
-
Isolation
TCC-80I/80I-DB9: 2 kV
-
RS-485 Data Direction Control
ADDC® (automatic data direction control)
-
Terminator for RS-485
N/A, 120 ohms, 120 kilo-ohms
-
Baudrate
300 bps to 115.2 kbps
-
RS-232
TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
-
RS-422
Tx+, Tx-, Rx+, Rx-, GND
-
RS-485-4w
Tx+, Tx-, Rx+, Rx-, GND
-
RS-485-2w
Data+, Data-, GND
-
Input Current
TCC-80: 30 mA @ 5 to 12 VDC
TCC-80-DB9: 30 mA @ 5 to 12 VDC
TCC-80I: 20 mA @ 5 to 12 VDC
TCC-80I-DB9: 20 mA @ 5 to 12 VDC -
Input Voltage
5 to 12 VDC
-
No. of Power Inputs
1
-
Overload Current Protection
Supported
-
Power Consumption
TCC-80/80-DB9: 30 mA @ 5 to 12 VDC
TCC-80I/80I-DB9: 20 mA @ 5 to 12 VDC -
Source of Input Power
Power input jack
Moxa serial converters TCC-80I-DB9 Series
If you have any interest, pls feel free to contact me as below
Jackie Ma
HONGKONG XIEYUAN TECH CO., LIMITED
Add:7-A16,Caishen Commercial Plaza,Hangkou Railway Station,Wuhan, China
M:86-15717178751(WhatsApp & Telegram) | T:+86-27-85887732 | F:86-27-85309780
Email:Jackie@hkxytech.com
